What We Fix
A cooktop drops into the counter as its own appliance, separate from the oven below, and gas and induction models fail in completely different ways. We service Wolf gas and induction cooktops, Thermador gas, induction, and Freedom induction cooktops, and Gaggenau gas and Vario induction cooktops across Brookville. On the gas side we work on the sealed burners, spark ignition, and gas valves. On the induction side we work on the coils, power boards, temperature sensors, and glass-touch controls.
Common repairs include spark electrode and igniter switch replacement, sealed-burner cleaning and alignment, gas valve service, induction coil and power-board replacement, pan-detection sensor faults, unresponsive or erratic touch controls, cooling-fan service, and clearing error codes that lock out a zone. Because induction cooktops run high-power electronics under the glass, cooling and sensor faults are as common as coil failures.
Common Problems
- A gas burner clicks but will not light. The igniter sparks while the burner stays cold.
- A gas burner keeps clicking after it lights. The spark continues even with a flame present.
- An induction zone will not detect a pan. The zone shows a pan symbol or error even with compatible cookware in place.
- A zone shut off with an error code. The induction cooktop cut power to one zone to protect the electronics.
- The touch controls are unresponsive or erratic. The glass surface will not respond, or zones change on their own.
- An induction zone runs weak or cycles. A zone heats slowly or pulses on and off, a sign of a coil or power-board fault.
Typical Causes
On gas cooktops the usual causes are a worn spark electrode, a burner cap that has shifted or absorbed a spill, clogged burner ports, and moisture around the igniter that keeps a burner clicking after it lights. On induction cooktops the story is electronic: a failed induction coil or power board for a specific zone, a pan-detection sensor that no longer reads compatible cookware, a blocked or failed cooling fan that overheats the electronics and forces a shutdown, and touch-control faults from moisture or a cracked control glass. Because induction electronics run hot, a clogged cooling path in a cabinet with poor ventilation is a frequent cause of intermittent zone shutdowns.
Brands We Service
Wolf, Thermador, and Gaggenau are the cooktops we see most in Brookville, spanning both gas and induction. Wolf repair covers sealed gas burners and Wolf induction, while Thermador Freedom induction and star-burner gas cooktops and Gaggenau Vario induction are common in Post Road and the Whitney estates kitchens. Induction cooktops report numeric error codes at the affected zone, so we read the code first, verify the coil, sensor, and cooling path, and then replace the specific board or component rather than swapping the whole surface.
Symptom, Cause, and What We Do
| Symptom | Likely Cause | What We Do |
|---|---|---|
| Gas burner clicks but will not light | Worn spark electrode, clogged port, or misaligned cap | Clean and align the burner, replace the electrode, verify a steady flame |
| Induction zone will not detect a pan | Failed induction coil or pan-detection sensor | Confirm cookware compatibility, test the zone electronics, replace the coil or sensor |
| Zone shuts off with an error code | Blocked cooling fan or failing power board | Read the code, clear the cooling path, replace the fan or power board |
| Touch controls unresponsive or erratic | Moisture under the glass or a control-board fault | Dry and test the control, replace the touch board if the fault persists |
| Burner clicks after it lights | Moisture or debris around the igniter | Dry and clean the electrode area, reseat or replace the cap |
If you smell gas near a cooktop, do not attempt to light a burner. Shut the gas off, ventilate the room, and call your utility if the odor is strong. On an induction cooktop, a cracked or chipped glass surface should be taken out of service and repaired promptly, since a crack exposes the high-power electronics underneath to spills and moisture.
Common Questions
Why Does My Induction Cooktop Not Recognize My Pan?
My Gas Cooktop Burner Clicks Constantly Even After It Lights. How Do You Fix It?
My Induction Cooktop Shows an Error Code and Shut a Zone Off. What Causes That?
Related Repairs
Range Repair
Wolf, Viking, and Thermador ranges with sealed burners, igniters, and oven faults.
View range repair → BrandGaggenau Repair
Vario induction, gas cooktops, and integrated appliances with coil and control faults.
View Gaggenau repair → ProblemBurner Not Igniting
Why a sealed gas burner clicks without lighting and how we restore a clean flame.
View burner guide →